Murakami Aquasol HVP 5 GALLON

Murakami Aquasol HVP 5 GALLON

On sale $297.46
Part Number:ANC00032
Aquasol - HV
APPLICATIONS
PHYSICAL PROPERTIES
HANDLING
SENSITIZING
MESH PREPARATION
COATING PROCEDURE
DRYING
Aquasol-HVP
APPLICATIONS
PHYSICAL PROPERTIES
HANDLING
SENSITIZING
MESH PREPARATION
COATING PROCEDURE
DRYING
MURAKAMI Aquasol HVP Aquasol HVP AquasolHVP Aquasol HVP
MURAKAMI SCREEN USA, INC. 745 Monterey Pass Rd. Monterey Park, CA 91754
TEL: 323.980.0662, FAX: 323.980.0659 www.murakamiscreen.com
Pure Photopolymer emulsion for Plastisol
Discharge and Water-based textile ink
systems.
• Pink colored PVA-SBQ Pure Photopolymer
 Direct Emulsion
• Pre-sensitized for immediate use
• Fast exposures, 3-5x faster than diazo
 based emulsions
• Excellent for use with Plastisol as is, or for
 Discharge and Water-based ink systems
 when 8 grams of diazo per gallon is added
 and when hardened with Murakami
 Hardeners. (MS or A&B Hardeners)
• Virtually pin hole and fish eye free
• Extremely durable on press
• Outstanding resolution and definition
 properties
• 42% solids content.
Handle under yellow safelights. Avoid
exposure to sunlight, flourescent and
incandescent lights.
This PVA-SBQ emulsion is ready to use.
There is no need to add sensitizer.
See special applications on the back of this
page for water base and discharge inks.
It is important to remove any contamination,
residual inks, cleaning chemistry, or general
dirt and dust. Murakami 701 Haze/Ghost
Remover (a non-caustic water soluble liquid)
will remove residual ink and/or emulsion.
Murakami 801 Screen Degreaser will help
eliminate any further contaminants.
Completely dry the screen before coating.
• Use a clean dry coating trough that has
 a nick free surface for smooth coating.
• Apply one or two coats of emulsion to the
 print side. Rotate the frame 180 degrees
 and apply one or two coats of emulsion
 to the squeegee side.
• Additional coats may be added to the
 print side if thicker stencils are required.
Dry the coated screen horizontally with the
print side down in a clean light safe area.
The following will help to ensure complete
drying:
• 86° to 104° degrees F (30° to 40° C)
• 30% to 50% relative humidity
• Good air circulation
The use of a screen drying cabinet with
heated airflow can help in maintaining
these conditions.
PRODUCT TECHNICAL DATA SHEETAquasol HVP Aquasol HVP Aquasol HVP
EXPOSURE
WASHOUT
RECLAIMING
STORAGE AND HANDLING
SPECIAL APPLICATIONS
MURAKAMI Aquasol HVP
MURAKAMI SCREEN USA, INC. 745 Monterey Pass Rd. Monterey Park, CA 91754
TEL: 323.980.0662, FAX: 323.980.0659 www.murakamiscreen.com
• Use Murakami 501, 505 or 507 Screen
 Cleaner to remove all excess ink from the
 frame.
• Remove the emulsion with Murakami 601,
 605, or a solution of Strip Super-P. Rinse
 thoroughly.
• Use Murakami 701 to remove haze and
 ghost if required.
• Degrease with Murakami 801, rinse both
 sides thoroughly and let dry.
Store the emulsion in a cool dry area.
Pre-sensitized emulsion has a minimal
shelf life of at least one year when stored
at room temperature.
Use Murakami PVA-SBQ emulsion
within one year for best results.
Coated screens may be stored for up to
one month when kept under the following
conditions.
• 59° to 77° degrees F (15° to 25° C)
• 30% to 50% relative humidity
Clean the film positives and vacuum frame
glass prior to exposure to minimize
pinholes. Exposure is affected by mesh
color, emulsion type, coating thickness,
lamp type and the age of the bulb itself.
For best results use an exposure
calculator to determine the correct
exposure time. It is important that a
lamp designed for exposing screen
printing emulsions is utilized.
Note: The use of film positives that are
either frosted or have weak black density
can reduce resolution and definition
qualities of the coated screen.
Mesh/Inch Color Seconds
 86 55-65
 110 50-60
 200 70-90
 300 60-80
 350 35-50
W
W
Y
Y
Y
Gently spray both sides of the screen with
cold to lukewarm water, wait a few seconds
to allow emulsion to soften then wash print
side of screen until image is fully open. Rinse
both sides thoroughly and dry. The use of a
drying cabinet or fans is recommended to dry
the screen. Use a pressure washer on fan
spray for developing the screen.
Note: All exposure times listed above are
suggested times using a 5KW Metal Halide
lamp at a distance of 40”. Add 25% to exposure
time when diazo is added for water
base and discharge inks.
Suitable for use with water based and
discharge inks when diazo is added and screen
is hardened with Murakami MS Hardener and/or
Hardener A&B. Stencils treated with Hardener
A&B will be harder to reclaim. Add only one
third of a bottle of water to diazo bottle and
shake well before adding to emulsion.

Related Items